●高粘度泵優點：

　　轉子泵的軸向位置可調，不需要拆泵。

　　泵采用模塊化設計，可根據不同的使用要求更換不同部件。可選夾層結構，以方便對泵加熱或冷卻，可以選擇是否帶安🏃‍♀️全閥，可以選擇不同的密封形式，詳見密封結⭐構圖。泵的各個零件可以選用不同的材質以㊙️适應具體使用要求。

　　不同的使用條件，泵的結構形式可能不同，具體應用請向廠家或本公司客戶代表咨詢。需要指出的🌐是泵🔞的轉速愈高，泵✏️的磨損愈嚴重，液體中如含有磨料物質，泵的材料應選用耐🏃磨材質，在此種工況下，泵的壓力和轉速都應降低，高溫條件下，則應增加泵的間隙，并采用耐熱材料 。

　　流動穩定：流量與齒輪轉速成正比，與壓力無關

　　流動平穩：沒有脈動和壓力波峰，不會産生管道顫動。

　　多功能性：僅僅通過調整轉子軸的位置，同一台泵既🔞可以出來稀釋溶液又可以出來瀝青，糖漿，樹脂🙇‍♀️，聚合物等高粘😍度液體。

　　可逆性：可以通過改變齒輪的旋轉方向使液體反向流👨‍❤️‍👨動，兩種方向都能充分發揮泵的性能

　　自吸性：由泵産生高真空，允許在最大自吸高度實現快速自🈲吸✂️，取決于泵送液體的物理特性（溫度，蒸汽壓力，粘度等）。

　　建議性：隻有兩個活動部件：主動輪和動輪，隻有一個軸封。

　　堅固的重載結構：低轉速。特大球軸承的外部軸承座可以承💚受軸向和徑向負載。

　　磨損率低：由于主動輪和從動齒輪不成倍數關系。這㊙️就意味着磨損可以被均(jun1)勻的分散在每個齒輪上。因為一❤️個齒輪上的每一個齒輪接觸另一個齒輪上的每一個齒輪的次數一樣。

磨損調節系統：轉子邊緣的磨損可以通過調整轉子軸的位置來補償。這樣，即使在有相當大的磨損的情況下，也可以保☔證泵的穩定性。

　　維護簡單，維護率低：不用移動泵，管道或泵驅動裝置就🥰可以進行檢查和調節。

　　互動性：标準組件的設計可實現不同材料和特性零部件💁之間的替換。例如：有多種軸封系統可供選擇，還可以安裝✔️帶夾🐇套的外殼和軸蓋來代替标準部件。

　　端口位置可改變：泵殼可在軸承箱上旋轉以從不同位置處🎯吸排液體。

　　預熱：加熱夾套或是與外殼鑄成一體，或是安裝在端蓋上，或是安裝在填料壓蓋上。

　　旁路安全閥：旁路安全閥安裝在泵上并且容易調節📐，在有🌈些💃🏻型号的泵上采取雙重安全閥并帶加熱🍓夾套。

●NYP高粘度泵的進出口

　　泵進出口的型式

　　常規泵進出口尺寸相同，進出口呈垂直布置，從驅動機向泵頭方向看為右進上出。也可根據客戶需要，加工成水平進出口型或左進上出型。連接方式有法蘭型和螺紋型.

　　泵進出口負荷

　　泵在安裝時，應限制泵的進出口所承受的管路負荷。螺紋聯接💋的管接頭不得承受負荷，否則會使泵的聯接管産生松動或旋緊力矩（管螺紋聯接處不允許有旋緊或松動的扭矩，以免）影響管路的聯接效果。

●NYP高粘度泵的起動

　　泵在起動過程中應特别注意以下幾個問題：

　　起動前要檢查下列内容：

　　檢查泵、齒輪箱和電機的對中程度；

　　檢查過濾器中有沒有焊皮和金屬渣；

　　檢查各連接部位連接是否緊固；

　　檢查管路壓在泵上的力和力矩是否超過給定的數值，如果溫度較高，還應檢查管路是否有膨脹節；

　　檢查電氣連接的正确性及電機的額定值，并檢查電機轉動方向是否正确；

　　檢查泵的轉動方向是否正确；

　　如有安全閥，安全閥安裝必須正确，

　　檢查泵軸是否轉動靈活；

　　泵的内部不能是幹的，特别是需要自吸的時候，應向泵内灌注一些油或輸送的液體；

　　泵組裝時在零件的表面有防護液，如果這種液體不🈲能和✂️泵送液體相容，則必須清洗；

　　最好在管路上安裝壓力表和真空表，方便觀察泵的工🚩作狀态；

　　檢查機械密封箱是否注滿液體；

　　檢查管路的閥門是否打開；

　　如果用内燃機驅動，請在起動發動機前保持離合器脫開；

　　泵起動後，檢查液體是否進入到泵中，泵是否工作🔴正常，如🧡果長時間無液體進入泵中，應停機檢查泵🐉及管路。

●高粘度齒輪泵并不能産生壓力，它隻是輸出流量。壓力低或無壓力，說明高粘度齒 輪泵沒有吸入液體或洩漏嚴重。High viscosity gear pump does not generate pressure, it is only the output flow.Pressure is low or no pressure, high viscosity gear wheel pump don't inhale the liquid or leakage is serious.

　　電動機輸出功率偏小、齒 輪泵排量選得過大或壓力調得過🧑🏽‍🤝‍🧑🏻高🆚時，也會造成壓力不足 當然，壓力表損壞或壓力表節流孔🐅堵塞🌈時也顯示不出壓力，此時可換裝一個新的壓力表檢查。Small motor output power, gear wheel pump capacity to choose too large or pressure too high, can cause stress Pressure gauge damage or pressure gauge orifice jams, of course, also could not show pressure, can change a new pressure gauge to check at this time.

　　如果确認泵無流量輸出，可能是由于泵安裝有誤♉、泵的轉向不對，或吸人側(進液口及吸液管道)堵塞、出口止回閥裝反或卡死了，也有可能是驅動軸斷裂⁉️了。If confirmed that no flow pump output, could be turned to the pumps due to pump installation is wrong, wrong, or suction side (liquid into the mouth and suck liquid pipeline jam, export check valve installed backwards, or card is dead, it is possible that the drive shaft fracture.

　　高粘度泵在轉速過低時會引起出液量不足，這種現象🎯往🐕往🐕是🔱由于泵的驅動裝置打滑或功率不足所緻🍓。此時應檢🔆查齒✍️ 輪泵的實際轉速、泵與電動機的聯接及功率匹配情況等。High viscosity pump in low speed can cause insufficient quantity of produced liquid, this phenomenon is often due to the slippage of the pump drive or insufficient power.Check the gear wheel pump at this time of the actual speed, pump and motor connection and power matching, etc.

● 高粘度泵開機準備

　　在開始運轉前，往齒輪泵的殼體内灌滿待輸送的液體，便于安全啟動。若環境溫度低于冰點，應預先向泵内通入熱蒸汽，進行預熱處理🚶，然後才可啟動齒輪泵。高粘度泵的旋轉方向要與進、出油口相符。齒輪泵若是第一次運行，或長期閑置後再使用，最好在空🐪載或小負荷情況下先跑合一小時左右。如果在跑🈲合階段預先覺察出異常溫升、洩漏、振動和噪聲時，應停機檢查。高🌈粘度齒輪泵的支座或法蘭與其驅動電機應采用共同的安裝基礎，基礎、法蘭或支座均需具有足夠的剛度，以減小齒輪泵運轉時産生的振動和噪聲。電動機與齒輪泵須用彈性聯軸器連接，同軸度小于0.1毫米，傾斜角不得大于1度。安裝聯軸器時不得用錘敲打，以免傷害齒輪泵的齒輪等零件。若用帶輪、鍊輪等驅動時應設托架支承💁，以防主動齒輪軸承受徑向力。緊固齒輪泵、電動機的地腳螺釘時，螺釘受力應均勻，連接可靠。用手轉動聯軸器時，應感覺到齒輪泵能夠輕松地轉動，沒有卡緊等異常現象出現，然後🔞才可以配管。High viscosity pump before starting work, to gear pump casing filled with liquid, facilitate safe launch.If the environment temperature is below freezing, should advance to pump into the hot steam, preheating treatment, and then to start the pump.The direction of rotation of the pump with high viscosity, oil outlet in accord.Gear pump is the first run, or long-term idle before using, had better under the condition of no load or small load to run one hour or so.If in the running-in stage in advance detect abnormal temperature rise, leakage, vibration and noise, should stop check.High viscosity gear pump bearing or flange should adopt a common drive motor installationFoundation, foundation, flange or support all needs to have enough rigidity, to reduce the vibration of gear pump is running and noise.Motor and gear pump with elastic shaft coupling, coaxial degree is less than 0.1 mm, Angle shall not be greater than 1 degree.When installing coupling hammer shall not be used, in order to avoid damage of the gear pump gearAnd other parts.If use the belt wheel, wheel, etc, shall set bracket support, in case of driving gear bearing by the radial force.Ground screw fastening gear pump, motor, screw force should be uniform, reliable connection.Turn the coupling with the hand, should feel can easily turn the gear pump, no abnormal phenomenon such as clamping, then can be piping.

     高粘度齒輪泵的吸油管道内徑應足夠大，并避免狹窄通道或急🌍劇拐彎、減少彎頭，去除不必要的閥門、附件，盡可能地降低泵的安裝高度，縮短吸油管道的長度，以減少壓力損失。管接頭等元件的密封要良好，以防止空氣侵入，從而控制氣穴與氣蝕的發生。止回閥與安全閥在齒輪泵的輸出管路上最好安裝一個止回閥。這樣在檢修🤟泵及輸💜出管道時，系統中的液體不會發生倒流。齒輪泵帶負荷停車時，亦可防止泵倒轉而在其輸出管道🐆内産生局部真空。應當注意，出口止回閥不能裝反或出💃現卡死現象。高粘度泵的出口管路上還應當設置安全閥等保護裝置，這樣一旦泵的出口通道發生堵塞，就可以打開安全閥🆚卸壓。安全🥵閥可以與🔱泵體或泵蓋鑄成一體，也可以單獨裝配。對于需要正反轉的高粘度齒輪泵，其進出口管路上均需設置安全閥。High viscosity gear pump oil suction pipe diameter should be large enough, and to avoid the narrow channel, or a sharp turn, reducing elbow, remove unnecessary valves, fittings, as much as possible to reduce the installation height of pump, shorten the length of the oil suction pipe, in order to reduce the pressure loss.Components, such as pipe joint sealed well, in order to prevent the air intrusion, thus control air-pocket and the occurrence of cavitation.Check valve and relief valve on the output of the gear pump tube had better install a check valve.In the overhaul pump and output pipe, the system of fluid backflow will not occur.Gear pump to stop loading machine, can be in the output pipe to prevent pump reverse, and create a partial vacuum.It should be noted that the outlet check valve cannot be installed backwards or stuck.High viscosity of the pump outlet pipe also shall set up relief valve or other protective device on the road, so that once the clogging pump export channels, can open the relief valve pressure relief.The relief valve can be cast and pump body and pump cover, also can separate assembly.For high viscosity gear pump need positive &negative, import and export all needs to set up the line safety valve.

   高粘度泵是輸送高粘度液體的齒輪泵，應做到在較低的功耗、較少的洩漏、較大的壓力下輸出🤩最🚩多的流量。在确定所要輸送的介質時，應該❗嚴格🔞遵循💋産品說明書上的規定，盡量使用廠家推薦的流體介質，并注意考慮系統的工🌈作溫度範圍。當希望在某一較寬的溫度範🔞圍内使用♌時，輸送介✍️質的粘度指數應該高些。輸送介質不僅是能量傳遞的中介，而且也是潤滑、密封及傳熱介質。液體粘🌏度過高會增加内摩擦阻力，降低輸出功率，浪費能💛量，并産生過高的系統溫度.高粘度齒輪泵的出口管路上應當設置安全閥等保護裝置，這樣一旦泵的👨‍❤️‍👨出⛷️口通道發生堵塞，就可以打開安全閥卸壓。對于需要正反轉的高粘度齒輪泵，其進出口管路上均需設置安全閥。High viscosity pump is conveying liquid with high viscosity gear pump, should be in lower power consumption, less leakage, under the pressure of large output the most traffic.When determining to conveying medium, we should strictly follow the provisions of the product manuals on use manufacturers recommend fluid as far as possible, and pay attention to consider the system operating temperature range.When you want to use in a wide temperature range, medium viscosity index should be higher.Medium is not only the energy transfer intermediary, but also lubrication, sealing and heat transfer medium.Liquid viscosity is too high will increase internal friction resistance, lower output power, waste of energy, and generate high temperature system. High viscosity gear pump outlet pipe shall set up relief valve or other protective device on the road, so once the clogging pump export channels, can open the relief valve pressure relief.For high viscosity gear pump need positive &negative, import and export all needs to set up the line safety valve.